跟踪uboot代码，了解imx6 splash image的生成过程。
涉及文件：
./cpu/arm_cortexa8/start.S
./board/freescale/mx6q_sabresd/mx6q_sabresd.c
./board/freescale/commom/fsl_bmp_reversed_600x400.c
/* 汇编调用C语言 */
./cpu/arm_cortexa8/start.S:ldr pc, _start_armboot @ jump to C code ------+
|
lib_arm/board.c <-----+
start_armboot(void)
{
......
/* 一系列初始化 */
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) { ---+
if ((*init_fnc_ptr)() != 0) { |
hang (); |
} |
} |
...... |
|
#if defined CONFIG_SPLASH_SCREEN && defined CONFIG_VIDEO_MX5 |
setup_splash_image(); --------------------|-+
#endif | |
...... | |
} | |
| |
init_fnc_t *init_sequence[] = { <--------+ |
#if defined(CONFIG_ARCH_CPU_INIT) |
arch_cpu_init, /* basic arch cpu dependent setup */ |
#endif |
board_init, /* basic board dependent setup */ ------+ |
#if defined(CONFIG_USE_IRQ) | |
interrupt_init, /* set up exceptions */ | |
#endif | |
timer_init, /* initialize timer */ | |
env_init, /* initialize environment */ | |
init_baudrate, /* initialze baudrate settings */ | |
serial_init, /* serial communications setup */ | |
console_init_f, /* stage 1 init of console */ | |
display_banner, /* say that we are here */ | |
#if defined(CONFIG_DISPLAY_CPUINFO) | |
print_cpuinfo, /* display cpu info (and speed) */ | |
#endif | |
#if defined(CONFIG_DISPLAY_BOARDINFO) | |
checkboard, /* display board info */ | |
#endif | |
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) | |
init_func_i2c, | |
#endif | |
dram_init, /* configure available RAM banks */ | |
#if defined(CONFIG_CMD_PCI) || defined (CONFIG_PCI) | |
arm_pci_init, | |
#endif | |
display_dram_config, | |
NULL, | |
}; | |
| |
/* imx6初始化文件 */ | |
board/freescale/mx6q_sabresd/mx6q_sabresd.c | |
int board_init(void) <-----+ |
{ |
/* need set Power Supply Glitch to 0x41736166 |
*and need clear Power supply Glitch Detect bit |
* when POR or reboot or power on Otherwise system |
*could not be power off anymore*/ |
u32 reg; |
writel(0x41736166, SNVS_BASE_ADDR + 0x64);/*set LPPGDR*/ |
udelay(10); |
reg = readl(SNVS_BASE_ADDR + 0x4c); |
reg |= (1 << 3); |
writel(reg, SNVS_BASE_ADDR + 0x4c);/*clear LPSR*/ |
|
mxc_iomux_v3_init((void *)IOMUXC_BASE_ADDR); |
setup_boot_device(); |
fsl_set_system_rev(); |
|
/* board id for linux */ |
gd->bd->bi_arch_number = MACH_TYPE_MX6Q_SABRESD; |
|
/* address of boot parameters */ |
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; |
|
setup_uart(); |
#ifdef CONFIG_DWC_AHSATA |
if (cpu_is_mx6q()) |
setup_sata(); |
#endif |
|
#ifdef CONFIG_VIDEO_MX5 |
/* Enable lvds power */ |
// setup_lvds_poweron(); |
|
panel_info_init(); -------------------+ |
| |
gd->fb_base = CONFIG_FB_BASE; | |
#ifdef CONFIG_ARCH_MMU | |
gd->fb_base = ioremap_nocache(iomem_to_phys(gd->fb_base), 0); | |
#endif | |
#endif | |
| |
#ifdef CONFIG_NAND_GPMI | |
// setup_gpmi_nand(); | |
#endif | |
| |
#if defined(CONFIG_ENET_RMII) && !defined(CONFIG_DWC_AHSATA) | |
setup_fec(); | |
#endif | |
| |
#ifdef CONFIG_MXC_EPDC | |
setup_epdc(); -------------------+ |
#endif | | |
return 0; | | |
} | | |
| | |
#ifdef CONFIG_VIDEO_MX5 | | |
void panel_info_init(void) <-------+ | |
{ | |
panel_info.vl_bpix = LCD_BPP; //屏幕颜色深度 | |
panel_info.vl_col = lvds_xga.xres; //屏幕尺寸 | |
panel_info.vl_row = lvds_xga.yres; //屏幕尺寸 | |
panel_info.cmap = colormap; | |
} | |
#endif | |
| |
static void setup_epdc(void) <-----------------------+ |
{ |
unsigned int reg; |
|
/*** epdc Maxim PMIC settings ***/ |
|
/* EPDC PWRSTAT - GPIO2[21] for PWR_GOOD status */ |
mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A17__GPIO_2_21); |
|
/* EPDC VCOM0 - GPIO3[17] for VCOM control */ |
mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D17__GPIO_3_17); |
|
/* UART4 TXD - GPIO3[20] for EPD PMIC WAKEUP */ |
mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_D20__GPIO_3_20); |
|
/* EIM_A18 - GPIO2[20] for EPD PWR CTL0 */ |
mxc_iomux_v3_setup_pad(MX6DL_PAD_EIM_A18__GPIO_2_20); |
|
/*** Set pixel clock rates for EPDC ***/ |
|
/* EPDC AXI clk (IPU2_CLK) from PFD_400M, set to 396/2 = 198MHz */ |
reg = readl(CCM_BASE_ADDR + CLKCTL_CSCDR3); |
reg &= ~0x7C000; |
reg |= (1 << 16) | (1 << 14); |
writel(reg, CCM_BASE_ADDR + CLKCTL_CSCDR3); |
|
/* EPDC AXI clk enable */ |
reg = readl(CCM_BASE_ADDR + CLKCTL_CCGR3); |
reg |= 0x00C0; |
writel(reg, CCM_BASE_ADDR + CLKCTL_CCGR3); |
|
/* EPDC PIX clk (IPU2_DI1_CLK) from PLL5, set to 650/4/6 = ~27MHz */ |
reg = readl(CCM_BASE_ADDR + CLKCTL_CSCDR2); |
reg &= ~0x3FE00; |
reg |= (2 << 15) | (5 << 12); |
writel(reg, CCM_BASE_ADDR + CLKCTL_CSCDR2); |
|
/* PLL5 enable (defaults to 650) */ |
reg = readl(ANATOP_BASE_ADDR + ANATOP_PLL_VIDEO); |
reg &= ~((1 << 16) | (1 << 12)); |
reg |= (1 << 13); |
writel(reg, ANATOP_BASE_ADDR + ANATOP_PLL_VIDEO); |
|
/* EPDC PIX clk enable */ |
reg = readl(CCM_BASE_ADDR + CLKCTL_CCGR3); |
reg |= 0x0C00; |
writel(reg, CCM_BASE_ADDR + CLKCTL_CCGR3); |
|
panel_info.epdc_data.working_buf_addr = CONFIG_WORKING_BUF_ADDR; |
panel_info.epdc_data.waveform_buf_addr = CONFIG_WAVEFORM_BUF_ADDR; |
|
panel_info.epdc_data.wv_modes.mode_init = 0; |
panel_info.epdc_data.wv_modes.mode_du = 1; |
panel_info.epdc_data.wv_modes.mode_gc4 = 3; |
panel_info.epdc_data.wv_modes.mode_gc8 = 2; |
panel_info.epdc_data.wv_modes.mode_gc16 = 2; |
panel_info.epdc_data.wv_modes.mode_gc32 = 2; |
|
panel_info.epdc_data.epdc_timings = panel_timings; |
|
setup_epdc_power(); |
|
/* Assign fb_base */ |
gd->fb_base = CONFIG_FB_BASE; |
} |
|
#ifdef CONFIG_SPLASH_SCREEN |
void setup_splash_image(void) <-------------------------+
{
char *s;
ulong addr; s = getenv("splashimage"); if (s != NULL) {
addr = simple_strtoul(s, NULL, 16);#if defined(CONFIG_ARCH_MMU)
addr = ioremap_nocache(iomem_to_phys(addr),
fsl_bmp_reversed_600x400_size);
#endif
/* 显示uboot图片 */
memcpy((char *)addr, (char *)fsl_bmp_reversed_600x400, ----+
fsl_bmp_reversed_600x400_size); |
} |
} |
#endif |
/* bmp文件生成的源文件 */ |
board/freescale/commom/fsl_bmp_reversed_600x400.c |
const unsigned char fsl_bmp_reversed_600x400[] = { <-----+
......
}
Author
Tony Liu
2016-8-9, Shenzhen
